Parts & Accessories

- High performance adhesive tape, a great pairing with Velox Cement - Each roll is usually adequate for gluing two tubular tires - Protects tube from spoke/nipple/rim puncture

Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's Standard Tubeless Kit converts standard tubed wheels to tubeless so you can reap the benefits. Everything you need to go tubeless is included. Plus, you won't miss dealing with flat tires and you'll save money on tubes!

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

- Replacement rear wheel skewer. - Specifically designed for use with Saris trainers. - Can be used for both indoor and outdoor rides.

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.

Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted. - DT Swiss Rear End Caps - QR x 135/142mm

These rim valves are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Key features: - To be used exclusively with Bontrager Tubeless Ready (TLR) wheels - Required for Bontrager's Tubeless Ready (TLR) system setup - Removable valve core for easy sealant fill - Silver MTB valve is compatible with all Bontrager Mountain wheels except: Line XXX, Kovee XXX, and Line Pro 40 - Alloy Road Tubeless Rim Valve is compatible with all Bontrager alloy TLR road wheels

Getting the correctly sized magnets means you're worrying about where the next coffee stop is, not if your computer is recording the ride. Key features: - Universal wheel magnets work with any speed sensor - Thread-on speed magnet is positioned closer to the sensor for improved signal - Aero speed magnet provides a sleek, low-profile, aerodynamic solution

Zipp 101 XPLR MOTO Rim Strip And Tubeless Tape Kit (includes rim strip and tubeless tape for 1 wheel).

This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation. The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included. - 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center - Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels - Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels - Includes cassette spacer - Material: Aluminum

Includes rim strip and tubeless tape for 1 wheel.

- Wheel bearing kit front/rear - Bearing dimensions: 17 x 30 x 7mm - Material: steel - 2 pieces

Wheel Conversion Caps for Zipp 77/177 Disc hubs. Converts your Zipp 77 or 177 hubs to nearly any frame standard.

Package comes with two pieces of rim tape for use with the Zipp clinchers. Woven nylon material. Tape is extra thin with a thickness of 0.5 mm. Note: For Zipp 700c and 650c aluminum/carbon hybrid clichers, use the 16 mm rim tape. For Zipp 30 wheel set use 18mm but for the wider Firecrest and Firestrike carbon clinchers use the 20mm x 1/2mm rim tape.

- Kits include Freehub body with CeramicSpeed bearings pre-installed for easy installation onto the wheel - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings

- Lowest resistance hybrid ceramic (ceramic balls and steel cages) available - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - Kits include Freehub body with CeramicSpeed

Freehub bodies for Zipp Cognition hubs.

- Freehub for Cognition V2 hubs

These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals. Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.

A simple solution for completing the Zipp aerodynamic package by covering the valve access hole on most disc wheels. Black, self-adhesive oval patches with the Z logo, in a package of five.

Wheel Freehub Kit—(Includes Bearings & Pawls) 11/12 Speed XD—X0 HUBS/RISE 60 (B1)/ROAM 30/ROAM 40/RAIL 40/RISE XX/ROAM 50/60 (B1) Compatible With: HU-X0-A1, WH-RAIL-40-A1, WH-RISE-60-B1, WH-RISE-XX-A1, WH-ROAM-30-A1, WH-ROAM-40-A1, WH-ROAM-50-A1, WH-ROAM-50-B1, WH-ROAM-60-B1

Wheel Freehub Kit—XD Driver Body Kit—Zipp ZM2 - Compatible With: WH-MOTO-30-B1

Wheel Freehub Kit SRAM XDR for Super 9RB - Compatible only with the Super 9 - Compatible With: WH-SP9-CCR-A1

Wheel Freehub Kit—XD Driver Body Kit—ZM1 3Zero - Compatible With: WH-MOTO-30-A1

Rear Wheel Axle for X0 hubs, including the following wheels: Rise 60 (B1), Roam 30, Roam 40, Rail 40, Rise XX, Roam 50, 60 B1 Compatible with part numbers: HU-X0-A1, WH-RAIL-40-A1, WH-RISE-60-B1, WH-RISE-XX-A1, WH-ROAM-30-A1, WH-ROAM-40-A1, WH-ROAM-50-A1, WH-ROAM-50-B1, WH-ROAM-60-B1

- Hub axle end cap set, rear - Zipp Cognition V2 Disc Brake - Rim brake compatible with XDR & 11-speed